Are you currently looking for content concerning How to Install a Bathtub?
Mounting a bath tub isn't specifically brain surgery, however it does need solid plumbing, carpentry, and sometimes, tiling abilities. Changing an old tub with a new one is also a reasonably tough job. If the old bathtub is easily available, the task can relocate quickly; if you have to open a wall to remove the old tub and position the brand-new bath tub, the job is a lot harder. In either instance, the task is within a house handyman's abilities, although you will need a helper to move out the old tub and also embeded in the brand-new one. Make certain you have certified on your own for the task as well as are comfortable attempting it. Rather than hiring a service provider to take control of a halfway-completed job, it is much better to consider employing one prior to you start. Possibilities are you may require an expert plumber to make tube connections.
This article will certainly assist you install a new tub in your restroom if you have currently gotten a new tub and also do not need to change the setup of your previous water system pipes.
Your tools and also product checklist should make up the following:
Planning for the Setup
Firstly, the sustaining framework supplied with the bath needs to be fitted (if needed) according to the manufacturer's directions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is important to make certain that if the tap features a plastic washer, it is fitted in between the bath and the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps unit to avoid strain on the bath tub.
Fit the versatile faucet ports to the bottom of both taps making use of 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet with the hole in the bath. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you use every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath must now prepare to be fitted in its last placement.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your setup, then the first thing you must do is disconnect the water system. After doing so, activate the taps to drain pipes any water continuing to be in the system. The process of eliminating the existing faucets can be quite bothersome due to the limited accessibility that is typically the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the taps. Have a fabric all set for the continuing to be water that will come from the pipelines. As soon as the supply pipes have been eliminated, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from turning during this process. When the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Prior to going on to fit the new taps, compare the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Installing the Tub
Utilizing both wood boards under its feet, place the bathtub in the needed setting. The wood boards are handy in evenly spreading out the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four little factors.
The following objective is to make certain that the bathtub is leveled all round. This can be achieved by checking the spirit level as well as changing the feet on the bath tub till the level reviews level.
To install taps, fit the bottom of the furthest versatile tap port to the proper supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water and also examine all joints and also brand-new pipework for leakages and also tighten them if necessary. Fill the bathtub and additionally examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as defined in the supplier's user's manual. Tiling as well as securing around the tub ought to wait up until the bathtub has been used at least when as this will certainly resolve it right into its final setting.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic connector to prevent damages to the string. One end of the port fits on the plastic tail of the tap and the other end provides a link to the current supply pipelines.
If you need to fit a monobloc, then you will certainly need reducing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin ensuring that the washers remain in location between the faucet as well as the sink. Protect the tap in position with the maker offered backnut. Once the faucet is safely in place, the supply pipes can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with normal faucet ports. The former kind must be linked to the tap finishes first, tightening just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the location where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the fitting can move sufficient to crack an inflexible seal, triggering the water to penetrate the wall surface between the bathroom as well as the tiling, leading to issues with dampness and also possible leakages to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures as well as fittings. They are offered in tubes and cartridges, as well as are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the bathtub with water prior to sealing, to enable the activity experienced when the tub remains in use. The sealer can crack relatively very early if you do not consider this activity before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly readily available on the market. It is a good idea to fit the floor tiles using waterproof or water-proof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you appreciate reading up on Installing A Bathtub? Write a short review directly below. We will be glad to find out your responses about this review. We hope that you visit us again later on. In case you enjoyed reading our article if you please do not forget to pass it around. Thanks a lot for your time. Visit again soon.
This Resource